Logo

SPILS Panel

SPILS Panel

The SPILS Panel is like the Oxygen Panel but has an additional illuminated press button. This small addition will make this panel quite a bit more complicated.

SPILS Panel

SPILS BITE Switch

Procedure:

There is a light source to this panel so it has to be made of the specified 3 mm acrylic if the back lighting is required.
1. 3D print the five parts (C, D, E, F and G) that make up the BITE switch.
2. Paint parts F and G black.
3. Using a small paint brush paint the LED bays of part F silver.
4. Press fit the cherry keyboard switch in the bottom ...
5. Place the spring over the plunger.
6. Insert the plunger into the cross shaped projection from the keyboard switch.
7. Insert the LED insert into the outer part.
8. Press the top assembly into the bottom assembly.
9. Laser cut the bottom 2 layer in a laser cutter using clear 3 mm acrylic sheet.
10. By hand use a medium drill bit to make the 2 M3 screws holes either side of the BITE switch opening chamfered.
11. Laser cut the bottom layer in a laser cutter using white 3 mm acrylic sheet.
12. Laser cut the middle layer in a laser cutter using white 3 mm acrylic sheet.
13. Laser cut the top layer in a laser cutter using white 3 mm acrylic sheet.
14. Paint the top layer grey.
15. leave the protective film on the top and bottom of the middle layer and paint the edges grey.
16. Remove the file from the top and botton of the middle layer.
17. Engrave the two vertical marks through the paint on the middle layer.
18. Engrave the text through the paint on the top layer.
19. 3D Print 2 DZUS caps and 2 DZUS grommets.
20. Paint DZUS Caps grey.
21. Attach the switch to the bottom 2 layer with the slot towards the bottom of the panel.
22. Place the four layers together and secure with 2 M3x12 mm screws through the three holes.
23. Place the bottom, middle and top layers together and secure with 2 M3x40 mm screws through the DZUS grommits.
24. Press DZUS caps over the DZUS grommets.
25. Connect the cable to each side of the ON/OFF switch.
26. 3D print the five parts that makeup the BITE switch.
27. Place a white LED in the top and an amber LED in the bottom of BITE switch openings and connect wires to the LEDs.
28. Laser cut a 1 mm thick white diffuser for the top of the switch.
29. Laser cut a 1 mm thick clear legend for the switch.
20. Laser engrave the lettering into the clear legend and use black paint to fill the letters in.
31. Attach diffuser then the clear legend to the BITE switch.
32. Attach BITE switch to the bottom 2 layer with two M3 countersunk screws.



SPILS Panel BITE SWitch Arrachment

Files:

Note all .SVG files are 96dpi.

Part Description File Type
A DZUS Cap DZUSCap.stl 3D print
B DZUS Grommets DZUSGrommet.stl 3D print
C SPILS Bite Switch Outer SPILSBITESwitch_Outer.stl 3D print
D SPILS BITE Switch Standoff SPILSBITESwitch_Standoff.stl 3D print
E SPILS BITE Switch Plunger SPILSBITESwitch_Plunger.stl 3D print
F SPILS BITE Switch Inner SPILSBITESwitch_Inner.stl 3D print
G SPILS BITE Switch Middle SPILSBITESwitch_Middle.stl 3D print
H SPILS BITE Switch Diffuser SPILSPanelBITESwitch_Diffuser.svg Laser cut
J SPILS BITE Switch Lens SPILSPanelBITESwitch_Lens.svg Laser cut and engraved
1 Top Layer SPILSPanel_TopLayer.svg Laser cut and engraved
2 Middle Layer SPILSPanel_MiddleLayer.svg Laser cut
3 Bottom Layer SPILSPanel_BottomLayer.svg Laser cut
4 Bottom Layer 2 SPILSPanel_BottomLayer2.svg Laser cut
5 M3 flat washer (x3)
6 M3x16mm pan headed cross-cut screws (x3)
7 Switch toggle ON/OFF ST-SP
8 M3x40mm pan headed cross-cut screws (x2)
9 Switch, momentary, Cherry keyboard
10 Spring, Compression, 0.8mm dia wire, 14mm dia, 15mm length.
11 Amber 3mm 3v LED
12 White 3mm 3v LED
13 M3x25mm countersunk screws (x2)
14 (not shown) M3 nut (x7)